LOST-Chall
http://lost-chall.org/forum/

13#There's No Place Like Home II
http://lost-chall.org/forum/viewtopic.php?f=5&t=157
Page 1 of 1
Author:  Bregi [ Tue Jun 24, 2008 8:42 pm ]
Post subject:  13#There's No Place Like Home II

It's possible that something isn't working quite well, so let me know here.

And be prepared for the final Season 4 Challenge, but that will take at least 1 month to create :twisted:

Greez
Author:  criple_ripper [ Tue Jun 24, 2008 9:26 pm ]
Post subject: 

hey Bregi!!very nice challenge...it's a bit weird to find out how these commands work...i'm still searching how to write them... :evil: but anyway...in the form the variables must be posted in your "temp" page abcdeftest.php or theres-no-place-like-home-ii.php?
Author:  Bregi [ Wed Jun 25, 2008 4:26 am ]
Post subject: 

I've just deleted abcdeftest, that was just for me ;)
Seen that you solved it. Gratulations!

Bregi :twisted:
Author:  criple_ripper [ Wed Jun 25, 2008 8:44 am ]
Post subject: 

you deleted the file but now the challenge doesn't work...:)
i think you must change the action in your form...
it was hard to solve it in the requested commands but after looking at it for 40 minutes BAM i got it...great challenge Bregi!!!
many thanks...
Author:  sabretooth [ Wed Jun 25, 2008 12:39 pm ]
Post subject: 

I fixed it.

Amazing that Bregi can make challenges this complicated yet still make some very basic mistakes xD


sabre
Author:  Bregi [ Wed Jun 25, 2008 4:39 pm ]
Post subject: 

oh damn yes now I realize it ;)
BUT hehe, yesterday I was working 3 hours on this challenge and after finished it (it was named abcdeftest.php this time) I forgot to change the action name :P
OK, now it works. Thanks sabre :P
Greez
Author:  sabretooth [ Thu Jun 26, 2008 2:29 pm ]
Post subject: 

Bregi, please check that this challenge works correctly. I still think there are problems with it.

Ian
Author:  criple_ripper [ Thu Jun 26, 2008 4:23 pm ]
Post subject: 

hey sabre...in my opinion(and Bregi's too) that challenge works fine...we tested it and we found 2 possible solutions...
Author:  Bregi [ Thu Jun 26, 2008 4:51 pm ]
Post subject: 

Ok, I now made a little change in the picture, I removed the
'All incremental (0,0)' information first it was wrong and 2nd I think it could confuse you as a challenger.
Right would be Absolute 0,0. That means (in CNC programming) it all starts from 0, you don't put in the y coordinate and if you are for example at
5 and go 3 up you wont be and 2, you will be on 3.

Hope that made it clearer
Greez
Author:  scorpio_the_first [ Sat Aug 09, 2008 3:05 pm ]
Post subject: 

great chall, finally managed to control "smokey". But I think the command in the notes for the diagonal moving needs to be adjusted because the x/y coordinates are interchanged.

greez scorp
Author:  Bregi [ Sat Aug 09, 2008 3:18 pm ]
Post subject: 

scorpio_the_first wrote:great chall, finally managed to control "smokey". But I think the command in the notes for the diagonal moving needs to be adjusted because the x/y coordinates are switched.

greez scorp


Oh, might be, I'll take a look at it tomorrow..

Thanks for pointing it.

Bregi
Author:  thefinder [ Tue Jan 19, 2021 10:41 pm ]
Post subject:  Re: 13#There's No Place Like Home II

Hi, I think it's important to say the start is:
'N00 init S, move x,y,-z;'
It is not explain correctly in the note.
Page 1 of 1 All times are UTC